Omnia Industries Food Processor Omnia One Multicast Stero Audio Processor with SENSUS Bedienungsanleitung

Omnia ONE Multicast Stereo Audio Processor with ® Installation and Operation Manual Version MC 1.0 / September 2007 Applicable to OmniaONE units

OmniaONE Multicast - Use and Operation Manual – Version 0.90 10 and bandwidth limiting methods that were required for analog broadcasting, as well as

OmniaONE Multicast - Use and Operation Manual – Version 0.90 11 So… what’s so smart about Sensus®? The fact is, Sensus® is smart. In real time it pr

OmniaONE Multicast - Use and Operation Manual – Version 0.90 12 S A F E T Y I N S T R U C T I O N S 1. Read All Instructions. All safety and o

HAZARD / WARNING LABELS The Exclamation Point symbol, within an equilateral triangle, alerts the user to the presence of important operating and ma

CE CONFORMANCE – This device complies with the requirements of the EEC Council Directives: 93/68/EEC (CE Marking); 73/23/EEC (Safety – low voltage dir

Manual Update Notification Audio Processing – a unique art form that we take very seriously! As part of our dedication to the science of audio proc

OmniaONE Multicast - Use and Operation Manual – Version 0.90 16

Chapter-1: Installation Pre-Installation Tasks Please take a few minutes to read through this chapter before proceeding with the installation. This

Installation & Connections Throughout this section reference is made to “software parameters.” These are part of the User Interface, which is cov

Rear Panel Connections Analog Audio Inputs and Outputs Balanced XLR-type connectors are used as input connectors for the analog audio. Both ana

OmniaONE Multicast - Use and Operation Manual – Version 0.90 2

AES/EBU Digital Input, AES/EBU External Sync Input, and AES/EBU Output (GREEN Male XLR) (GREEN Female XLR) (RED Female XLR) The digital AES

RS-232 Modem Connection (DB-9M) This DB9-male connector can be used to connect an external dialup modem for a bi-directional computer remote control

General Purpose Interface (GPI) (DB-9F) This DB9-female connector serves as a four-input, optoisolated interface to the Omnia's internal Trigger

Chapter-2: Getting To Know Your OmniaONE The OmniaONE User Interface Now that your OmniaONE is rack-mounted, connected to a program audio source, a

Audio I/O Level Display Either input or output levels can be displayed. The highest LED illuminated indicates digital sample-accurate peak signal lev

Using the Jog Wheel The main user control for the OmniaONE is the easy to use jog wheel with its integral push-switch. Using the control is both intu

Main Menu The OmniaONE menu system has been designed to be intuitive and simple to use. Most operating parameters are found under one of the menu he

¾ The factory default selection for Input Source is Analog. To change the input selection to AES/EBU digital, rotate the jog-wheel until [AES/EBU] is

OmniaONE Multicast - Use and Operation Manual – Version 0.90 28

Chapter-3: Getting The Sound You Want In general, applications requiring audio processing prior to a codec don’t rely heavily on absolute loudness fo

January, 2007 Welcome to Omnia.ONE! I wish to offer my sincere gratitude on behalf of our company and welcome you to Omnia.ONE! This manual was as

The following sections are provided to assist you in designing the personality of your sound. As we said earlier, there is no precise recipe for setti

Some users prefer their processing to be perceptibly loud but very dynamic. While this may not result in the loudest sound, it gives the illusion of c

The last option, adjusting the Mixer, is designed to provide a final minor trim to the audio spectrum. Since this stage is after all of the dynamic m

Chapter-4: Main Menu Selections This section presents an overview of the five Main Menu items, (Preset:, Processing, Input/Output, Administrative an

Save Preset This option saves any changes you have made to the currently running preset into the OmniaONE’s non-volatile memory. Changes can be saved

Rename Preset A preset in the list of stored user presets can be renamed at any time. Factory presets cannot be renamed. To rename a user preset hi

Wideband AGC (Automatic Gain Control) The wideband AGC rides the incoming audio levels like an automatic “hand on the fader”, keeping the average leve

Enhancers Deep Bass Adds ‘girth’ to the audio by enhancing very low frequencies such as kick drum fundamentals or very low bass notes that may be pr

Adjusts the amount of gain reduction in the Presence Band AGC. Higher numbers result in more drive and because of the increased compression,

RTZ Speed (Return To Zero Speed) RTZ stands for Return To Zero. What RTZ does is return the gain of the AGC band to the selected amount of gain red

OmniaONE Multicast - Use and Operation Manual – Version 0.90 4

The release control adjusts how fast the limiter recovers from periods of more gain reduction when the input audio levels fall. Faster release times (

to the Mixer the same This allows you to reduce the Low Band Mixer control to reduce IM distortion in the Final Limiter without reducing the amount of

Hi Band Adjusts the output level of the high band limiter into the overall mix. Higher numbers result in more high frequencies and too much m

This type of peak controller is used instead of a clipper because it does not generate the same high levels of harmonic distortion as a Clipper does.

1 The Nyquist Theorem states that the maximum frequency that may be applied to a sampled data system is one half the sampling frequency. When signal

This submenu provides level adjustments for the audio inputs and the absolute peak operating level of the Analog, AES-3 (AES/EBU) and Livewire output

Right Trim Allows a +/-3dB adjustment of the right analog audio channel gain to correct minor left/right balance problems in the input audio.

[Mono L+R] - Configures the DSP processing chain to have both the Left and Right internal channels fed from the sum of the Left Channel and Right Chan

[Input] Slaves the output sample rate to the sample rate present on the Omnia’s AES digital input. Synchronization is possible over

character is found, click. This will return the cursor to “select” mode and you can again turn the knob to select the next character to edit. -To del

OmniaONE Quick-Start Setup We know that you’re probably in a hurry to begin using your new OmniaONE Multicast. If you have technical expertise and pr

<-Exit Click on this option to return to the Main Menu. Administrative Several maintenance and utility functions are found in this submenu

When selected, initiates a complete system reset, which includes reloading the internal operating system, DSP processing code, and values from

Rotate the jog wheel and click on “OK” to lock the front panel or “Cancel” to return to the Main Menu without locking the front panel. The factory d

Note: All measurements made using "Bypass" mode, which is available in the Input/Output menu. General Audio Specifications Frequency Respo

Connector: EMI-suppressed RJ-45 female pinned according to StudioHub+® standards. Transformer isolated, balanced, and floating according to AES3 sta

Power Supply: Internal. Overvoltage and short circuit protected. Meets EN55022, EN55011 Level B Conducted Emissions. EN61000-4-2, -3, -4, -5, -6 lev

Appendix B: Troubleshooting/Service/Warranty Operational problems with the OmniaONE can sometimes be

troubleshooting techniques for isolating possible OmniaONE problems in the field, and also how to obtain help or repair service from Omnia. To take c

A report similar to the below will be generated. You can select the text and then copy and paste into an email or email a screen shot to if requeste

When actually troubleshooting your OmniaONE, try to ascertain some preliminary information first before embarking on an in-depth problem-solving missi

OmniaONE Multicast - Use and Operation Manual – Version 0.90 6 Welcome to Omnia.ONE!...

Obtaining Service • Omnia Customer Support personnel are available in Cleveland, Ohio, USA, Monday through Friday between 9:00 A.M. and 6:00 P.M., E

Warranty This Warranty covers "the Products," which are defined as the various audio equipment, parts, software and accessories manufa

OmniaONE Multicast - Use and Operation Manual – Version 0.90 62

Appendix C: Remote Control and Software Update Procedure Remote Control The above screenshot shows the Processing screen of the OmniaONE’s built-i

The Main Menu should appear: Click on the “Remote” link option from the top menu or “Meters & Remote Control” option from the Main Menu.

To delete a preset, click the “Delete Preset” button. A new applet window will open with a preset list. Highlight the preset to be deleted in this pre

Processing Click on the “Processing” tab and the block diagram will appear: Each block is a button that can be clicked to open a new applet window c

Clicking on the “In” tab will display all of the controls for the OmniaONE’s Input menu in the main applet screen. Adjustment of the controls works

Please note that Trigger Script functionality is not yet implemented in the current software but will be available with a free downloadable software u

software is always uploaded to the inactive bank. This is a safeguard against loss of power or other interruption during the update. In this event,

OmniaONE Multicast - Use and Operation Manual – Version 0.90 7 Preset...

OmniaONE, the following “Update Initiated” screen should appear: 7. Now the software bank that is not currently in use will be updated with the new

You will notice that the previous software (Bank 0 in this case) is still selected and running. You can choose to change to the other bank to acti

OmniaONE Multicast - Use and Operation Manual – Version 0.90 8 Appendix B: Troubleshooting/Service/Warranty....

.Multicast Sensus® Technology: Audio Processingx3 Overview Until now, digital signal processing has been a more precise numeric implementation of